The fourth race of Zwift Racing League 2025/26 Round 2 happens Tuesday, November 25, and it’s a team time trial on the new Watts the Limit route in NYC. This is an interesting TTT route, with plenty of pitch changes to keep us on our toes and unique characteristics that make it a much faster course than you might think.
Let’s dig into crucial segments, escalators, bike choice tips, and more!
Looking at the Route
Watts the Limit is a fresh route from the recent New York map expansion. And while the Strava segment profile (above) may look lumpy – like a city skyline, in fact – it’s actually a fairly flat and fast route, thanks to escalators helping us out of the subway tunnels!
All categories will race a full lap of this out-and-back route, for a total of 31km with 219m of elevation. (Although it’s not really 219m, since ~95 of those meters are on escalators.)
Most of this course is close to pan-flat, with major elevation changes taking place quickly in between as you enter or exit subways. Here are the key points you’ll keep in mind as your team attacks this course:
- Lead-In Kicker @1km (300 meters at 3.7%): this little bump near the end of the lead-in is short enough that it’s best to just hammer hard if you’re on the front, and stay in the draft if you’re behind. Keep the watts high so your speed stays up, then grab recovery on the flats and descents that follow.
- Escalator @4.7km: the first of six escalators you’ll encounter today, these are going to play havoc with teams who have riders with widely varying weights. See “More On Escalators” below for details.
- Escalator @8.2km
- Manhattan Bridge @9.1km (1.2km at 1.6%): the bridge isn’t as steep from this side, so speeds will stay high and drafting will remain very important. Increase your power, but stay in formation. Recovery awaits on the back half of the bridge.
- Escalator @14.5km
- Hill to Grand Army Plaza @14.6km (400 meters at 2%): this little climb comes directly after the escalator, so keep the power up in order to maintain speed all the way up to the flat Grand Army Plaza turnaround at the top.
- Escalator @18.7km
- Manhattan Bridge @19.5km (1.1km at 2.4%): a bit steeper on this side, but still not a proper “climb,” so you’ll definitely want to lift the power while staying in formation up and over.
- Escalator @24.5km
- Escalator @27.8km
- Final Kicker @30.5km (300 meters at 3.7%): almost there! Hammer this kicker just like you did at the start of the race, then go all-in across the top to empty the tank and finish fast.
- Finish at 31km
More On Escalators
Warning: the new escalators in NYC may prove tricky if there’s a big difference between the highest and lowest rider weights on your team!
Community feedback is saying, and our tests are confirming, that heavier riders slow much more on the escalators than lighter riders. (Heavier riders, take heart: Zwift knows about this issue, and internal sources tell me a change is planned soon to make escalators perform much more uniformly across various riders. Light riders: enjoy the escalators while you still can! 😁)
I ran bots of various weights up one of the longer escalators on the route (the final escalator you’ll hit, in fact). Each bot’s power was set so they would all have approximately the same escalator entry speed (~46 kph), and that power remained steady as they went up and over the top of the escalator. Here’s how much each bot slowed down between entering and exiting the escalator:
- 50kg bot @261W: slowed 3.2 kph
- 75kg bot @339W: slowed 11 kph
- 100kg bot @390W: slowed 16.1 kph
Of course, most teams won’t have a 50kg (or even 25kg) weight difference between riders. But the heavier you are, the more you should plan to push on escalators to keep your speed high. And lighter riders will probably want to keep their power fairly steady, to avoid shooting off the front!
Two more escalator tips:
- Lower Your TD: These are steep, with gradients around 20%. If you have trainer difficulty set to 100%, it will feel like pedaling into a wall. I recommend setting TD to 50% or less for this course.
- Follow the Wheels Down: The downhill ramps will also wreak some havoc due to varying rider weights and power outputs. Pay close attention and try to maintain your single-file position before, during, and after descending the ramps to maximize your draft benefit and keep speeds high. If you’re a lighter rider on the front during one of these descents, hammer out some of the watts you’ve saved on the escalators, as the heavier riders will fly past otherwise!
Read more about the Watts the Limit route >
Bike Frame + Wheel Choice
Bike choice here is simple: go aero. On a flattish route like this, weight doesn’t matter much, and aero is everything! The best setup by far is the CADEX Tri frame paired with the DT Swiss Disc wheels, but you’ll need to be at level 40+ to access this sweet rig:
If you don’t have access to this setup, check out “Fastest TT Bike Frames and Wheels at Each Zwift Level” and use the fastest TT frame and wheelset available at your level.
One more note on bike choice: upgrading your frame makes a big difference. A fully upgraded frame saves around 13 watts, or ~48 seconds per hour of riding. Read all about the performance improvements you receive from upgrades here.
More Route Recons
Many recon rides are planned each week on the upcoming ZRL route. If you’re unfamiliar with this course, jump into an event and familiarize yourself with the route! Find a list of upcoming ZRL recon rides at zwift.com/events/tag/zrlrecon.
Additionally, riders in the Zwift community do a great job every week creating recon videos that preview the courses and offer tips to help you perform your best on the day. Here are the recons I’ve found (comment if you find another!):
J Dirom
John Rice
TTTips
Successful team time trialing on Zwift requires a challenging combination of physical strength, proper pacing, and Zwift minutiae like picking a fast bike, understanding drafting in a TTT context, and getting your frame fully upgraded.
Flatter courses like this week give valuable seconds to teams with big pure-power riders who can keep their power high on the front while staying in single-file formation to conserve in the draft behind. Extra seconds can also be gained by pacing smartly, ramping up the effort on short climbs and recovering a bit once you’re up to speed on the short descents.
On a course like this week’s, I highly recommend all team members set their Trainer Difficulty to the same value so you’re all feeling the gradient changes similarly. (When one rider has it set to 100% and another 25%, the first rider may ramp up power much more than the second when a climb hits, which can make a mess of your team formation.)
Your goal in a ZRL TTT is to get four riders across the line in the shortest time possible. That means every team’s pace plan will differ based on each rider’s abilities. I highly recommend having an experienced DS on Discord directing your team, especially if your team contains some inexperienced TTT riders.
Lastly, if you want to go further down the TTT rabbit hole, I highly recommend Dave Edmond’s Zwift TTT Calculator tool.
Questions or Comments?
Share below!
wpDiscuz
